Services

Electrical / Mechanical Diagnostic Testing Services


Explore

Residual Life Assessment/ Condition Monitoring


Explore

Induction Bolt Heating



Explore

1.ELECTRICAL & MECHNICAL DIAGNOSTIC TESTING SERVICES

Rotating machines

  • Turbines

    • NFT on Blades
    • NDT tests
  • Generator/Motors

    • Stators
    • Windings
      • Wedge Tightness Check (Mapping)
      • Winding Insulation Resistance
      • Over Voltage Proof Test (AC / DC)
      • Dissipation Factor and Tip-Up (Tan Delta and Capacitance Measurement)
      • Partial Discharge Test (Computerized)
      • Corona Probe / PD / TVA Test (Slot Discharges)
      • Bushing / Dielectric Losses
      • Surge Comparison Test
      • DC Winding Resistance
      • Natural Frequency (Bump) Test
      • Contact Resistance
    • Core
      • Visual Inspection
      • Electromagnetic Core Imperfection Detection (ELCID) / Low Energy Core Test
      • Loop Test / High Energy Core Test
      • Core Tightness Inspection
    • Rotor
      • Visual Inspection
      • Voltage Drop Test
      • Impedance
      • DC Winding Resistance
      • Insulation Resistance
      • Recurrent Surge Oscillograph (RSO)
      • Metallurgical Tests on retaining rings (DP & UT)
    • Exciter and PMG Tests
    • On-Line Tests
      • Partial Discharge Analysis (Testing, Installation and Commissioning)
      • Current / Electrical Signature Analysis
      • Vibrations
      • Acoustic Emission
      • IR Thermography
      • Harmonic Analysis Measurements


Transformers

  • Insulation Resistance

  • Dissipation Factor and Tip-Up (Tan Delta and Capacitance Measurement)

  • DC High Potential Test

  • Contact Resistance

  • Turns Ratio

  • HV Excitation Current

  • Short Circuit Impedance

  • SFRA (Sweep Frequency Response Analyzer)

  • Moisture Analyzer

  • Infrared Thermography ( On - Line )

  • Partial Discharge measurement


Power Cables

  • Insulation Resistance

  • DC Hipot / DC Step Voltage Test

  • Dielectric Loss / Tan Delta / Power factor / Capacitance measurement

  • Infrared Thermography ( On - Line )

  • “Online & Offline Partial Discharge Measurement”

  • “VLF & DAC”

Switch Yard

  • CTS

    • Burden measurement
    • Winding resistance measurement
    • Excitation Characteristics
    • Transient behavior
    • Ratio measurement
    • Phase and Polarity measurement
    • Accuracy limiting factor
    • Instrument Security factor
    • Secondary Time Constant
    • Remanence factor
    • Transient Dimensioning factor
    • Knee point voltage / current
    • Tan Delta / Capacitance Measurement
  • Lightning (surge) Arrestors

    • Insulation Resistance
    • Watts Loss Test
    • Leakage Current
  • Power Capacitors

    • Tan Delta / Capacitance Measurement
  • PTS

  • Circuit breakers

  • HV, LV, Neutral Bushings

  • Infrared Thermography ( On - Line )

  • Partial Discharge measurement



2.RESIDUAL LIFE ASSESSMENT/ CONDITION MONITORING

Residual Life Assessment (RLA) of equipment / Plant is the quantitative evaluation of the interaction of all the operation loads which could be steady as well as transient in nature resulting into corresponding stresses/strains (static/dynamic) and the material defects/degradation under the operating environment (high temperature, abrasive, corrosive etc.) This quantitative evaluation results into assessment of the remnant life of equipment under given operating conditions and material integrity. This assessment also helps in identifying the components of the equipment/plant to be repaired / replaced and their timing.

Life assessment aims at finding suitability of the component for further services under given operating conditions. This is best judged by ascertaining (a) the operational integrity of the equipment prior to shut down and (b) structural integrity of the components during shut down. Operational Integrity Analysis involves Evaluation of present performance and Analysis of past operations, failures, maintenance. Structural Integrity Analysis involves Design audit stress/vibration analysis and detailed examination of NDT, modal analysis. This coupled with analysis data of past operations/failures/problems encountered and strength calculation for the given structural integrity of the component, gives an idea of the remnant life, repairs and replacements to be undertaken and the their timing etc.

Assessing the condition and remaining life of power plant components operating at high temperatures and at high stresses is necessary to optimize inspection and maintenance schedules, to make RUN, REPAIR, REPLACE decisions and to avoid unplanned outages. While two different approaches are available for Residual Life Assessment of Power Plant components, one using data analysis based on operational history and the other based on periodic examination of critical components, the latter method is widely adopted as it is more accurate since it does not rely on standard material data with their associated uncertainties and does not necessarily require knowledge of the operational stress-temperature data.


monitoring

Methods based on periodic examination involve :

  • Various NDT techniques for detection of cracks, effects of corrosion / erosion etc. in addition to commonly adopted techniques such as Ultrasonic thickness gauging, Ultrasonic flaw detection, Penetrant testing, Fluorescent magnetic particle testing, Specialized techniques such as assessment of hydrogen damage by Ultrasonic, measurement of steam side oxide scale by in-situ ultrasonic, bore sonic inspection of rotors, eddy current examination of rotor blades and root, video probe examination of critical components are employed.

  • Metallurgical tests such as in-situ metallography using replica method, in-situ chemical analysis by metal spectroscope / X-ray fluorescence method, in-situ hardness measurement etc.

  • Sampling of component specimens for detailed laboratory analysis. This paper deals with the periodic inspection approach adopted by Industrial Quality Concepts for Residual Life Assessment of power plant components

3.Induction Bolt Heating

Global privatization, and the economic demands of the competitive market, is forcing power plant owners to examine operational efficiency and outage times. Privatization has also encouraged development of gas turbines. Gas turbines typically require maintenance every two years, and owners must closely evaluate turbine outage times. Swift and efficient bolt removal is vital. Both break out and box up times for the turbine are critical, and operators have to optimize these.


monitoring

Induction heating, which was first introduced in the USA by Manning’s, exposes the conductive bolt material to an alternating magnetic flux, via an electric wand, causing heat to be generated within the bolt. When exposed to an alternating magnetic flux, eddy currents are set up in the bolt. The flow of these eddy currents through a conductive mass dissipates as heat, according to the I2R law. Induction heating is faster and more accurate for thermally stretching bolts than conventional heating.


This proven method reduces outage time by days, the process minimizes safety concerns associated with the forceful removal of nuts with sledgehammers and slugging wrenches.

Features:

  • Shortens the heating time, and significantly reduces the working hours for bolt tightening and relaxation.
  • Less thermal expansion of flange due to rapid heating and highly precise clamping.
  • Easy to operate and only the bolt is extended, so it can be tightened and untightened with little force.
  • It can be applied to the existing bolts.
;

About Us

Powertest Asia is an ISO 9001:2008 Certified Company and provides total Diagnostic Testing Services on Electrical Power Equipment and Turbines.

Powertest Asia is headquartered in Hyderabad, India but supports clients all over the world. In addition to India, Middle East and South & East Asia, PtA executed projects in Africa and South America.

Contact

Head Office:
Powertest Asia Private Limited,
26, Vikaspuri,
Opposite to E.S.I Hosptial,
S.R. Nagar Post,
Hyderabad,
Telangana - 500 038
INDIA

E-Mail :
info@powertestasia.com

Phone:
+91-40-2371-3343
+91-40-2371-7752

BRANCH OFFICES:

CHHATTISGRAH



INTERNATIONAL OFFICES:

THAILAND
INDONESIA
MALAYSIA
UAE